Interinstrument comparison of remote-sensing devices and a new method for calculating on-road nitrogen oxides emissions and validation of vehicle-specific power

Emissions of nitrogen oxides (NOx) by vehicles in real driving environments are only partially understood. This has been brought to the attention of the world with recent revelations of the cheating of the type of approval tests exposed in the dieselgate scandal. Remote-sensing devices offer investigators an opportunity to directly measure in situ real driving emissions of tens of thousands of vehicles. Remote-sensing NO₂ measurements are not as widely available as would be desirable. The aim of this study is to improve the ability of investigators to estimate the NO₂ emissions and to improve the confidence of the total NOx results calculated from standard remote-sensing device (RSD) measurements. The accuracy of the RSD speed and acceleration module was also validated using state-of-the-art onboard global positioning system (GPS) tracking. Two RSDs used in roadside vehicle emissions surveys were tested side by side under off-carriageway conditions away from transient pollution sources to ascertain the consistency of their measurements. The speed correlation was consistent across the range of measurements at 95% confidence and the acceleration correlation was consistent at 95% confidence intervals for all but the most extreme acceleration cases. VSP was consistent at 95% confidence across all measurements except for those at VSP ≥ 15 kW t^?1, which show a small underestimate. The controlled distribution gas nitric oxide measurements follow a normal distribution with 2σ equal to 18.9% of the mean, compared to 15% observed during factory calibration indicative of additional error introduced into the system. Systematic errors of +84 ppm were observed but within the tolerance of the control gas. Interinstrument correlation was performed, with the relationship between the FEAT and the RSD4600 being linear with a gradient of 0.93 and an R² of 0.85, indicating good correlation. A new method to calculate NOx emissions using fractional NO₂ combined with NO measurements made by the RSD4600 was constructed, validated, and shown to be more accurate than previous methods.

Implications: Synchronized remote-sensing measurements of NO were taken using two different remote-sensing devices in an off-road study. It was found that the measurements taken by both instruments were well correlated. Fractional NO₂ measurements from a prior study, measurable on only one device, were used to create new NO_x emission factors for the device that could not be measured by the second device. These estimates were validated against direct measurement of total NO_x emission factors and shown to be an improvement on previous methodologies. Validation of vehicle-specific power was performed with good correlation observed.     

Larvicidal and pupicidal activities of eco-friendly phenolic lipid products from Anacardium occidentale nutshell against arbovirus vectors

Environmental Science and Pollution Research - Aedes aegypti and Culex quinquefasciatus are vectors of diseases that constitute public health problems. The discovery of products capable of...     

An integrated approach for assessing the migration behavior of chlorpyrifos and carbaryl in the unsaturated soil zone

Chlorpyrifos (O, O-diethyl O-3,5,6-trichloropyridin-2-yl phosphorothioate) and carbaryl (1-naphthyl methylcarbamate) are often applied concurrently as insecticides in food production. The aim of this study was to research their migration behavior in a real environment. We researched the leaching of both pesticides by setting up field lysimeters on a farm with the typical soil used in fruit production today. In order to analyze the variables involved in this process, we performed complementary adsorption studies, we performed complementary adsorption studies using batches and undisturbed soil laboratory columns for both compounds. The results for pesticide transport through the lysimeters showed that less than 1% of chlorpyrifos was recovered in the leachates, while almost 17% was recovered for carbaryl. Having completed the experiment in undisturbed laboratory columns, soil analysis showed that chlorpyrifos mainly remained in the first 5 cm, while carbaryl moved down to the lower sections. These results can be explained in view of the sorption coefficient values (K_D) obtained in horizons A and B for chlorpyrifos (393 and 184 L kg^?1) and carbaryl (3.1 and 4.2 L kg^?1), respectively. By integrating the results obtained in the different approaches, we were able to characterize the percolation modes of these pesticides in the soil matrix, thus contributing to the sustainable use of resources.     

Review: recent advances in biogas purifying technologies

Biomethane production through biogas upgrading is a promising renewable energy for some industries which could be part of the equilibrium needed with fossil fuels consumption to achieve a sustainable society. This paper presents a comprehensive list of biogas upgrading technologies focused on carbon dioxide removal as well as recent advances reported by researcher with wide expertise in this topic. Additionally, an extensive costs–performance comparison among the technologies studied is discussed. Among the different alternatives, chemical scrubbing stood out to achieve high biomethane purities while cryogenic technologies proved to be effective against methane losses. Regarding the different costs, water scrubbing and membrane separation seem to be the most affordable techniques.     

Ovariectomy predisposes female rats to fine particulate matter exposure’s effects by altering metabolic,oxidative, pro-inflammatory,and heat-shock protein levels

Environmental Science and Pollution Research - The reduction of estrogen levels, as a result of menopause, is associated with the development of metabolic diseases caused by alterations in...     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Analysis and optimization on the biodegradable plate making process parameters using RSM-based Box–Behnken Design method

Journal of Material Cycles and Waste Management - The present research work focused on fabricating Biodegradable Plate (BD plate) composed of rice husk ash, bagasse and corn starch which is...     

Monitoring Biofilm Thickness Using A Non-Destructive, On-Line, Electrical Capacitance Technique

Abstact The present study was designed to evaluate indirect, non-invasive, on-line measurement of biofilm thickness using an electrical capacitance technique. Several assays were carried out and the results showed that, at a frequency of 1 kHz, electrical capacitance could be used to measure biofilm thickness indirectly (with a correlation coefficient of 0.9495). The reproducibility revealed by the assays was also highly satisfactory.However, in contrast to what was expected, there was an inverse relationship between electrical capacitance and biofilm thickness, i.e. electrical capacitance diminished with the increase in the biofilm thickness.The tests were also carried out at different frequencies (1 kHz, 10 kHz and 100 kHz)     

The Metallic Composition of Aerosols at Three Monitoring Sites in Korea During Winter 2002

In the present study, the distribution patterns of various metals were analyzed and compared using PM samples collected concurrently from three monitoring sites located in Korea (Seoul, Busan, and Jeju island) in December 2002. As these sites can represent metal pollution with different degrees of anthropogenic activities, their concentration levels were distinguished in a systematic manner in the order of Jeju, Busan, and Seoul. By comparing the present data sets with those measured previously from other locations in Korea and around the world, we attempted to diagnose the general status of elemental pollution on the Korean peninsula. Through an application of different statistical approaches, the major processes controlling elemental levels were assessed for each of the three study sites. The results indicated the importance of both crustal and anthropogenic sources in all sites with their relative roles varying significantly from each other. The results of the metal analysis data, when examined in relation to back trajectory analysis, confirmed that their concentration changes are affected quite sensitively with air mass movement patterns. The overall results of this study consistently indicated the contribution of a strong anthropogenic source area (e.g., China) to the observed metal concentration levels in the study area, but the strengths of such signals vary considerably across the Korean peninsula.